27 February - 1 March 2018 // Nuremberg, Germany

Posting print layout

What information should be shown in the print layout?

Create print layout
Exhibitors & Products embedded world 2018
Zoom product LOGO_MULTILINK Universal/ACP Debug Probes

MULTILINK Universal/ACP Debug Probes

LOGO_MULTILINK Universal/ACP Debug Probes

MULTILINK Universal/ACP Debug Probes

Request information Request information

Contact us

Please enter your personal information and desired appointment. You can also leave us a message.

Your personal information

Your message for us

Desired appointment during the exhibition

* Compulsory fields you must fill in.
Send
Your message has been sent.

You do not have a registration yet? Register now and use all advantages of the Exhibitor Database.

An error has occurred.

PEmicro's Multilink ACP and Multilink Universal are development interfaces which allow a PC access to the Background Debug Mode (BDM) or JTAG interface on ARM devices from several manufacturers (Multilnk ACP) and also many different NXP MCU architectures  (Multilink Universal). They connect between a USB port on a Windows machine and the standard debug connector on the target. Headers for the supported architectures are located under an easy access panel that flips open. Ribbon cables suitable for a variety of architectures are included.

By using the Multilink ACP or Multilink Universal debug probes, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.

These Multilinks work with PEmicro's in-circuit debuggers and flash programmers to allow debug and flash programming of the target processor. For many of the supported processors, P&E has a set of interface libraries allowing the user to write their own Windows based application which interacts with PEmicro's debug interface. LPCXpresso, Kinetis Design Studio, S32 ARM and Power, Somnium, IAR, Cosmic, Codesourcery, Keil, Atollic, and CodeWarrior software all support the use of PEmicro's Multilink ACP and Multilink Universal to develop and debug with NXP's Kinetis ARM devices.

This interface is USB 2.0 compatible, and it is also backwards compatible with USB 1.1 ports.

FEATURES:

  • USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
  • Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
  • Target Voltage: 1.8V-5.25V
  • Target Frequency: 16Khz-50Mhz (applies to HCS08,RS08,CFV1, S12Z, or HCS12X only)
  • Compatible with Kinetis, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices from many manufacturers.
  • Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
  • ARM device support includes both the JTAG and SWD protocols
  • Includes USB cable, Type A Male to Type B Male, 6-ft.
  • Auto-frequency detection + trimming capabilities for HCS08 devices.
  • Auto-frequency detection for HC(S)12(X) devices.
  • Generates programming voltage on RESET line for RS08 devices.

SUPPORTED DEVICES

  • ARM Cortex devices: (supported by Multilink Universal and Multilkink ACP)
  • NXP:Kinetis®, LPC
  • Atmel:SAMxxx
  • Cypress:PSoC® 4
  • Infineon:XMC
  • Maxim:MAX716xx
  • Silicon Labs:EFM32, SiM3
  • STMicroelectronics:STM32
  • Texas Instruments:LM3S, LM4, TM4C12x
  • Toshiba:TX00, TX03, & TX04

NXP 8-/16-/32-bit devices: (supported by Multilink Universal only)

  • S32
  • LPC
  • Qorivva
  • ColdFire +/V1
  • ColdFire V2/3/4
  • DSC
  • HC(S)12(X)
  • S12Z
  • HCS08
  • RS08
  • MAC7xxx

 

CYCLONE FX Programmers

LOGO_CYCLONE FX Programmers

CYCLONE Programmers

LOGO_CYCLONE Programmers

MULTINK Universal FX Debug Probe

LOGO_MULTINK Universal FX Debug Probe

PEmicro GDB Server for ARM devices

LOGO_PEmicro GDB Server for ARM devices
top

The selected entry has been placed in your favourites!

If you register you can save your favourites permanently and access all entries even when underway – via laptop or tablet.

You can register an account here to save your settings in the Exhibitors and Products Database and as well as in the Supporting Programme.The registration is not for the TicketShop and ExhibitorShop.

Register now

Your advantages at a glance:

  • Advantage Save your favourites permanently. Use the instant access to exhibitors or products saved – mobile too, anytime and anywhere – incl. memo function.
  • Advantage The optional newsletter gives you regular up-to-date information about new exhibitors and products – matched to your interests.
  • Advantage Call up your favourites mobile too! Simply log in and access them at anytime.