PEmicro's USB Multilink Universal FX is a high-speed, all-in-one development interface which allows a PC access to the Background Debug Mode (BDM) or JTAG interface on many different NXP MCU architectures and ARM devices from several manufacturers (see complete list below). The FX's high-speed USB interface allows communications between your Windows machine and the standard debug connector on the target. Connections to target MCUs are supported via the multiple headers located on the USB Multilink Universal FX. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included.
The USB Multilink Universal FX includes all the features of PEmicro's standard Multilink interfaces, plus these additional benefits:
Lightning fast! Up to 10X faster communications speed than P&E's other Multilinks*
Can provide power to the target MCU
I/O line clamping for added protection
Supports additional NXP devices
*The exceptional performance increases seen with the USB Multilink Universal FX are limited to synchronous architectures: All P&E-supported ARM devices, Kinetis, S32, MPC5xxx, Coldfire V2-V4, DSC, MPC5xx/8xx, and HC16/683xx.
The USB Multilink Universal FX is natively supported by recent versions of LCPXpresso, KDS, Somnium DRT, S32 ARM and Power IDEs, CodeWarrior® (10.x), current P&E software applications, and toolchains from many NXP partners including IAR, Keil, Somnium, Cosmic, Atollic, and Green Hills (check with the vendor for device compatibility).
High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
Can be used to power target MCU.
Target Voltage: 1.8V-5.25V
Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)
Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
I/O line clamping for added protection
Auto-frequency detection + trimming capabilities for HCS08 devices.
Auto-frequency detection for HC(S)12(X) devices.
Generates programming voltage on RESET line for RS08 devices.
ARM device support includes both the JTAG and SWD protocols.
ARM Cortex devices:
Silicon Labs:EFM32, SiM3
Texas Instruments:LM3S, LM4, TM4C12x
Toshiba:TX00, TX03, & TX04
NXP 8-/16-/32-bit devices:
Leider gibt es für diesen Aussteller kein deutsches Firmenprofil.
PEmicro is an industry trendsetter in hardware and software development tools for NXP and ARM Cortex microcontrollers. PEmicro takes pride in its committment to providing professional, low-cost development tools and prompt, knowledgeable customer support. PEmicro was founded in 1980 and incorporated in 1982 by Dr. David A. Perreault. PEmicro developed and marketed the first general purpose EPROM programmer. It was based on the Z80 microprocessor and provided the ability to reconfigure pinouts. The second product developed by PEmicro was an S100 bus-based ROM emulator. This product pushed forward the capability to rapidly develop microcomputer based systems. Having developed a large number of microcontroller / microprocessor systems including both hardware and software, PEmicro capitalized on this experience and began developing software development tools. Much of this effort was directed toward simulators and cross-assemblers. PEmicro developed the concept of an in-circuit simulator. This device combines the big features of a simulator with the added advantage of real IO. This concept was used in Motorola's (now NXP's) very successful promotion for the 68HC05K1 part called the KICS05. To assist with rapid and affordable product development, PEmicro developed the Multilink Universal and Multilink Universal FX - all-in-one development interfaces which support a broad range of NXP architectures - as well as the Tracelink, an advanced, sub-$1000 interface which supports external trace via NXP's CodeWarrior IDE. PEmicro also recently launched next genration CYCLONE and CYCLONE FX programmers. These programmers now feature large color touchscreens for easy manual operation. They support a broad range of ARM manufacturers and NXP architectures, and their operations can easily be automated. The CYCLONE FX programmers, as our flagship Cyclones, offer several powerful and unique enhancements to memory size, programming speed, and data security. Their USB host port also allows programming to be initiated and executed using a barcode scanner, which can be a time-saver for production lines that include a variety of products.