PEmicro's Multilink ACP and Multilink Universal are development interfaces which allow a PC access to the Background Debug Mode (BDM) or JTAG interface on ARM devices from several manufacturers (Multilnk ACP) and also many different NXP MCU architectures (Multilink Universal). They connect between a USB port on a Windows machine and the standard debug connector on the target. Headers for the supported architectures are located under an easy access panel that flips open. Ribbon cables suitable for a variety of architectures are included.
By using the Multilink ACP or Multilink Universal debug probes, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
These Multilinks work with PEmicro's in-circuit debuggers and flash programmers to allow debug and flash programming of the target processor. For many of the supported processors, P&E has a set of interface libraries allowing the user to write their own Windows based application which interacts with PEmicro's debug interface. LPCXpresso, Kinetis Design Studio, S32 ARM and Power, Somnium, IAR, Cosmic, Codesourcery, Keil, Atollic, and CodeWarrior software all support the use of PEmicro's Multilink ACP and Multilink Universal to develop and debug with NXP's Kinetis ARM devices.
This interface is USB 2.0 compatible, and it is also backwards compatible with USB 1.1 ports.
USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
Target Voltage: 1.8V-5.25V
Target Frequency: 16Khz-50Mhz (applies to HCS08,RS08,CFV1, S12Z, or HCS12X only)
Compatible with Kinetis, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices from many manufacturers.
Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
ARM device support includes both the JTAG and SWD protocols
Includes USB cable, Type A Male to Type B Male, 6-ft.
Auto-frequency detection + trimming capabilities for HCS08 devices.
Auto-frequency detection for HC(S)12(X) devices.
Generates programming voltage on RESET line for RS08 devices.
ARM Cortex devices: (supported by Multilink Universal and Multilkink ACP)
Silicon Labs:EFM32, SiM3
Texas Instruments:LM3S, LM4, TM4C12x
Toshiba:TX00, TX03, & TX04
NXP 8-/16-/32-bit devices: (supported by Multilink Universal only)
Leider gibt es für diesen Aussteller kein deutsches Firmenprofil.
PEmicro is an industry trendsetter in hardware and software development tools for NXP and ARM Cortex microcontrollers. PEmicro takes pride in its committment to providing professional, low-cost development tools and prompt, knowledgeable customer support. PEmicro was founded in 1980 and incorporated in 1982 by Dr. David A. Perreault. PEmicro developed and marketed the first general purpose EPROM programmer. It was based on the Z80 microprocessor and provided the ability to reconfigure pinouts. The second product developed by PEmicro was an S100 bus-based ROM emulator. This product pushed forward the capability to rapidly develop microcomputer based systems. Having developed a large number of microcontroller / microprocessor systems including both hardware and software, PEmicro capitalized on this experience and began developing software development tools. Much of this effort was directed toward simulators and cross-assemblers. PEmicro developed the concept of an in-circuit simulator. This device combines the big features of a simulator with the added advantage of real IO. This concept was used in Motorola's (now NXP's) very successful promotion for the 68HC05K1 part called the KICS05. To assist with rapid and affordable product development, PEmicro developed the Multilink Universal and Multilink Universal FX - all-in-one development interfaces which support a broad range of NXP architectures - as well as the Tracelink, an advanced, sub-$1000 interface which supports external trace via NXP's CodeWarrior IDE. PEmicro also recently launched next genration CYCLONE and CYCLONE FX programmers. These programmers now feature large color touchscreens for easy manual operation. They support a broad range of ARM manufacturers and NXP architectures, and their operations can easily be automated. The CYCLONE FX programmers, as our flagship Cyclones, offer several powerful and unique enhancements to memory size, programming speed, and data security. Their USB host port also allows programming to be initiated and executed using a barcode scanner, which can be a time-saver for production lines that include a variety of products.